Ok, I know this is outside of the norm for this page, I don’t really care.

Backstory: I buy things from estate auctions on hi-bid. Nobody else bid on this so I got it for the minimum bid, $2.50 USD.

It was missing the hdd, and it was in a filthy barn.

Side note: auctions are generally “as-is, where is” that means you pick these items up at the location of the estate, they usually pull things out and organize them, but they don’t clean them or anything usually.

I have an extra IDE HDD, so I threw that in and tried to install Windows XP. I got errors halfway through saying “setup cannot copy the file:”

Then I got it to go all the way through, but it won’t boot.

Then I got a system error that the HDD is not present.

I tried an IDE adapted SSD, still not recognized.

Then I got the HDD recognized again.

I figured I would check the ram: 1x 256MB. I threw in 2x512MB, that’s a neat trick.

I also swapped out the cd drive since it was having a hard time opening up anyway.

Now I’m back to, “setup cannot copy the file:”

Maybe a bad CD burn? Idk, it’s been awhile since I’ve done this.

  • dark_stang@beehaw.org
    link
    fedilink
    arrow-up
    6
    ·
    1 year ago

    That machine was built during the capacitor plague. It could have all sorts of weirdness going on. Have you ran any hardware diagnostics yet? Did you notice any distended caps when installing the hdd?

    • SkepticElliptic@beehaw.orgOP
      link
      fedilink
      arrow-up
      4
      ·
      1 year ago

      I looked over the caps and didn’t see anything. I did figure out that the HDD problem was simply a BIOS setting. The settings are not intuitive.

    • poweruser@lemmy.sdf.org
      link
      fedilink
      English
      arrow-up
      1
      ·
      1 year ago

      This was my thought too. Whenever you open one of these Dells you always see swollen, leaky capacitors. They can cause some very odd behavior, such as only booting exactly one in three times.

      Theoretically, it should be relatively straightforward to find and replace them if you were really dedicated

      • SkepticElliptic@beehaw.orgOP
        link
        fedilink
        English
        arrow-up
        3
        ·
        1 year ago

        The problem I’ve always had with mobo caps is the high heat solder they used. You either need to use an extremely high wattage heat source or you need to get a lower temp solder to bond to the existing solder so that you can melt it with a regular iron.

  • SkepticElliptic@beehaw.orgOP
    link
    fedilink
    arrow-up
    5
    ·
    1 year ago

    I swapped the system battery with a good one. Maybe it’s losing something on restart when the install actually completes.

  • nyan@lemmy.cafe
    link
    fedilink
    English
    arrow-up
    4
    ·
    1 year ago

    If the HDD is intermittently not being detected even in the BIOS, there’s probably an issue with the hardware involved. Flaky IDE port on the mobo? Bad power or data cable? Overheating? Or, as someone has already suggested, capacitor plague?

    I can’t remember whether Dells of that era had manufacturer hardware lockin issues or not.

    • SkepticElliptic@beehaw.orgOP
      link
      fedilink
      English
      arrow-up
      1
      ·
      1 year ago

      I swapped cables and etc. It turned out to be a bios setting for the drive. I think the bad battery just caused the settings to get wiped.

      Why it was intermittent like that makes no sense though, but it’s good after I figured out how to enable that drive number.

  • rhythmisaprancer@kbin.social
    link
    fedilink
    arrow-up
    4
    ·
    1 year ago

    Does it have a requirement for the first memory slot to be populated by something smaller than 256? Can you try a low end Linux OS just to get it up and running?

    • SkepticElliptic@beehaw.orgOP
      link
      fedilink
      arrow-up
      1
      ·
      1 year ago

      There is a bios setting for “os install” which limits the amount of available ram, I believe that is for older os’s. This one shipped at the very end of windows xp in around 2005.

    • SkepticElliptic@beehaw.orgOP
      link
      fedilink
      arrow-up
      3
      ·
      1 year ago

      It was my spare drive causing the issues!

      I figured out that I did not have the correct setting in the BIOS to enable drive 0 on the 1st ide bus. Then I kept having installation issues.

      I swapped back the SSD and installation went flawlessly!

      This is a desktop btw.

      It is using IDE drives, no sata ports at all. The Ram is DDR 400MHz.

      It doesn’t even have an AGP slot, only 3x PCI slots with a 56k modem card in one of them.