I was wondering if I could run an ethernet cable from my router inside to my shed and connect it to another router so I can have ethernet and wifi in my shed.
Yes, probably run an outdoor CAT6 cable and bury if needed.
There is no problem with doing that in principle, as long as the cable is protected and the run is less than about 100m.
If longer than 100m what would be different?
Theoretical maximum distance of ethernet.
Yes, you can run Ethernet from your home router to your shed.
Ideally you’d use conduit to protect the cable, or use Ethernet cable designed for outdoor use. However, I’ve seen normal Ethernet cables last 10+ years outside without issue.
As others have mentioned, ideally the router in the shed will have DHCP turned off, and the incoming line will go into one of the normal Ethernet ports (not the WAN/Internet port). This will allow two-way communication between your house and shed (IE, your computers, network drives, network printers, network cameras, etc. can all see each other no matter which router they are connected to). However, if you only need Internet you can just plug the Ethernet cable into the WAN/Internet port on the shed’s router.
I’ve seen normal Ethernet cables last 10+ years outside without issue.
Northern New England here, have had a UTP Cat 6 cable running from my house to the shed for about 5 years, I didn’t even bury it. Not suggesting its the right way to do it, but it works fine. I do network installs all day, last thing I feel like doing at home is work :p
You can, but depending on the setup you should be aware of a few things:
- make sure you don’t have a ground potential difference.
- use appropriate rated cabling and not plain UTP
- you may want surge protection on that line coming in from outside
Do your homework and stay safe.
Study hard, don’t do drugs
I just think fiber is cheaper and easier on these cases.
For these reasons I would personally use a poe switch in my house and a poe powered access point in the second building.
Can you?
Yes.
Should you?
Probably not.
I have $6000 worth of burned out electronics to help you understand that this in not the best idea.
I’d use fiber instead. If you are not using fiber and you insist on going with copper you need a really good burial AND really good surge protection on each end.
If your shed is only 15M away, you’ll be fine using CAT6 OSP shielded. It’s designed for direct burial so no conduit needed. If you are really concerned about anything getting fried make sure to use shielded RJ45 connectors and shielded patch panel.
I’ll have to ask my dad first, but I’ll get back to you.
you can but you should run fiber instead unless you want lightning to fry a bunch of your stuff
Or just use a surge protected hub at the shed end.
Lighting will travel thru fiber .
Permission granted
yes
Oy! you got a license for that?
I’d personally find a cheap switch with fiber ports on both ends and use fiber. It’s non-conductive so a lot of the complexity of grounding and lightning protection is off the table.
may cost a few hundred, but if you fry you’re pc in the shed from a lightning strike it will probably cost more than that.
2.5gb unmanaged switches with 10gb sfp ports can be found for $50-75ish new and sfp’s are maybe 10 a piece. Depending on the local market you may be able to find a used Cisco 3750 for $10-20. If you just need one port you can find a pair of 1gb media converters with sfp’s for about $60. You can find pre-terminated direct burial fiber in various lengths for $110 or so for 250 ft, if you want to go overhead run a steel wire and attach the fiber to it, but you probably still want the armored fiber.
Depending on the speed and line of sight, a wireless point to point bridge may be an option… you can find a pair for anywhere from $50 for 300mbps (I wouldn’t bet that’s real world, probably 50-100mbps) to much more expensive options (I ran 4 between 2 buildings at my last office that ran at very high, licensed frequencies that were probably $5k a piece, but they did 10gbps on a good day, and we’re pretty rock solid even in the rain)
Just do a point to point wireless link. Less issues with ground difference and no trenching to do.
If you do trench use fiber -not- Ethernet cable
I get downvoted every time I respond to one of these posts but hey why not…
I strongly suggest running Fiber with a media converter on each end. This reduces the potential for lightning to travel from 1 structure to the other. Removes grounding concerns. It is by far the safest option.
Yeah I am thinking of going this route
mikrotic switches with sfp+ are relatively cheap and get you 10GB/s. It’s what I use in my separated garage on a 30m run. Melanox makes the card and fiber modules that i use, they are cheap too since most of this will be decommissioned server hardware.
Also, lightning may be a real hazard.