I thought we used magnetrons and such, and the excessive heat was due to current inefficiency and control of the fusion process in containing the heat and it building up higher and higher.
Sorry im not any sort of scientist here but i thought energy could not be created or destroyed so to get a net-positive energy out we would need to keep feeding in fuel, is this correct?
And if so, how?
energy is not created nor destroyed, however something can change forms, which gives off energy.
how stars work in fusion is that their high pressure and high temperatures allow for the fusion of particles. hydrogren (1 protonl fuses with another to produce helium (2 protons). in a stars life, that cycle continues. elements fuse till it hits iron (the end point of fusion). which then a stars life.is considered dead and eventually black hole stuff starts to happen due to density of star.
the power is actually not “infinite” its limited by the fuel supply available (hydrogren), but the net energy in to energy out is positive if the fuel source exists.
The difficult bit is to keep the fuel fusing. At the temperatures and pressures that are needed to get atoms to fuse together the whole lot wants to blow itself apart. Being able to reliability sustain the reaction for any length of time is a big achievement.
Once we can get it to keep going, then yes, we can use the excess heat for power, although it’ll probably involve turbines rather than an old school steam engine type setup.
Melting actually is not a seriously issue as while the plasma is very hot, it also has very little mass. Sparks are also ludicrously hot but with their little mass contain very little energy so pretty much anything but dry tinder is going to extinguish them before they can do any damage. You want to avoid loss of containment because you will have to clean the reactor vessel and maybe replace a couple of wall tiles but that kind of failure is far from catastrophic.
Though of course with current designs the reactor walls do get hot because that’s how we intend to capture the energy: Pipe water through the walls to cool them, use the hot water to drive a couple of turbines. One of the holy grails to pine for after the current designs actually enter service is to look at ways to drive electrons in a wire directly from the plasma, no detour via heat. The other is aneutronic fusion.
One of the holy grails to pine for after the current designs actually enter service is to look at ways to drive electrons in a wire directly from the plasma, no detour via heat.
That’s actually really interesting, as I never heard of that before.
Yeah you’re absolutely right, damn that’d be one hell of a Holy Grail touchdown moment for Humanity if we could pull that off, the direct transference, no “middle man”.
One of the biggest obstacles to magnetic-confinement fusion is the need for materials that can withstand the tough treatment they’ll receive from the fusing plasma. In particular, deuterium-tritium fusion makes an intense flux of high-energy neutrons, which collide with the nuclei of atoms in the metal walls and cladding, causing tiny spots of melting. The metal then recrystallizes but is weakened, with atoms shifted from their initial positions. In the cladding of a typical fusion reactor, each atom might be displaced about 100 times over the reactor’s lifetime.
That’s not the plasma that melts anything but neutron bombardment. The containment and fizzling out issue is the same whether the plasma produces neutrons or just tons of EM radiation which is what I focussed on.
That sturdiness of the cladding things is an important factor when it comes to making cost-effective reactors, that is, the price you sell electricity for needs to cover replacement parts, but is not really that much of an issue when it comes to achieving fusion the materials we have are sufficient for that. Proxima Fusion (the Max Planck spinout) is working on those economical issues for their commercial prototype (early 2030), it remains to be seen whether they go for durable and expensive or cheap but needs to be replaced more often. Which isn’t unusual for power plants in general, none of them run 24/7 they get shut down for maintenance once in a while.
That’s not the plasma that melts anything but neutron bombardment.
I’m aware (I read the article, including the part I quoted you), but regardless of the source of the melting, there is a melting issue of the containment vessel that needs to be engineered away.
when talking about fusion, just think the conditions of stars/the sun. In order to function correctly, it has to be ridiculously hot.
The race for fusion is how to maintain it, and eventually have a net positive transaction of energy out, to energy in ratio.
Hotter than the sun. The sun has an enormous gravity pushing things along. To compensate we use more heat.
I thought we used magnetrons and such, and the excessive heat was due to current inefficiency and control of the fusion process in containing the heat and it building up higher and higher.
The heat is needed so atoms collide enough to fuse without the high pressure inside a star. The trick is keeping the reaction going.
Sorry im not any sort of scientist here but i thought energy could not be created or destroyed so to get a net-positive energy out we would need to keep feeding in fuel, is this correct?
And if so, how?
energy is not created nor destroyed, however something can change forms, which gives off energy.
how stars work in fusion is that their high pressure and high temperatures allow for the fusion of particles. hydrogren (1 protonl fuses with another to produce helium (2 protons). in a stars life, that cycle continues. elements fuse till it hits iron (the end point of fusion). which then a stars life.is considered dead and eventually black hole stuff starts to happen due to density of star.
the power is actually not “infinite” its limited by the fuel supply available (hydrogren), but the net energy in to energy out is positive if the fuel source exists.
I’m not an expert but I believe the fuel is hydrogen. Hydrogen atoms fuse together to produce helium + energy
Stupid guy here, being ridiculously hot is the whole point right? Isn’t a fusion reactor just an extremely complex steam engine?
The difficult bit is to keep the fuel fusing. At the temperatures and pressures that are needed to get atoms to fuse together the whole lot wants to blow itself apart. Being able to reliability sustain the reaction for any length of time is a big achievement.
Once we can get it to keep going, then yes, we can use the excess heat for power, although it’ll probably involve turbines rather than an old school steam engine type setup.
How are they even containing that heat as this is obviously warm enough to melt everything in existence (as far as I know)?
vacuum for isolation. Magnets, so the plasma stays in the middle and won’t touch the walls. Microwaves to heat it up from the outside.
It’s moreso keeping it contained at those temperatures, so that it does not melt the container that it’s in, and potentially explode.
There has to be some absolute next-level power backup to keep the containment field from failing.
Melting actually is not a seriously issue as while the plasma is very hot, it also has very little mass. Sparks are also ludicrously hot but with their little mass contain very little energy so pretty much anything but dry tinder is going to extinguish them before they can do any damage. You want to avoid loss of containment because you will have to clean the reactor vessel and maybe replace a couple of wall tiles but that kind of failure is far from catastrophic.
Though of course with current designs the reactor walls do get hot because that’s how we intend to capture the energy: Pipe water through the walls to cool them, use the hot water to drive a couple of turbines. One of the holy grails to pine for after the current designs actually enter service is to look at ways to drive electrons in a wire directly from the plasma, no detour via heat. The other is aneutronic fusion.
That’s actually really interesting, as I never heard of that before.
Yeah you’re absolutely right, damn that’d be one hell of a Holy Grail touchdown moment for Humanity if we could pull that off, the direct transference, no “middle man”.
From the link (for others like me and did not know what the word meant)…
Read the below from this article…
That’s not the plasma that melts anything but neutron bombardment. The containment and fizzling out issue is the same whether the plasma produces neutrons or just tons of EM radiation which is what I focussed on.
That sturdiness of the cladding things is an important factor when it comes to making cost-effective reactors, that is, the price you sell electricity for needs to cover replacement parts, but is not really that much of an issue when it comes to achieving fusion the materials we have are sufficient for that. Proxima Fusion (the Max Planck spinout) is working on those economical issues for their commercial prototype (early 2030), it remains to be seen whether they go for durable and expensive or cheap but needs to be replaced more often. Which isn’t unusual for power plants in general, none of them run 24/7 they get shut down for maintenance once in a while.
I’m aware (I read the article, including the part I quoted you), but regardless of the source of the melting, there is a melting issue of the containment vessel that needs to be engineered away.
Yes, and you won’t get me to argue here. I’m too experienced a smart-Alec to contradict another smart-Alec :)